The EO2 error can affect all AirJet™ and HydroJet™ Lay-Z-Spa hot tubs. There are a number of causes which can be fixed quickly and easily. Cause 1: Dirty filter. A dirty water filter can cause water flow issues resulting in an EO2 error.
How do I reset my lazy spa E02?
Pump needs to be reset.
- Watch the Thermal Reset Video.
- Turn the pump unit on at the mains.
- Press the test button once and leave it bleeping (leave for 10 seconds).
- Turn the pump unit off and unplug from the socket (leave for 10 seconds).
- Plug the pump unit back in and turn it back on.
How do you fix the code on a hot tub?
DR or DRY Error Message Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.
How do I reset my hot tub heater?
- Turn off the power to your hot tub at the breaker.
- Find your hot tub’s red high limit reset button, which may be on the heater itself covered by rubber.
- Next, press the red reset button, which will make a clicking sound when it has been reset.
What does EO2 mean?
EO2
| Acronym | Definition |
|---|---|
| EO2 | Equipment Operator Second Class (Naval Rating) |
| EO2 | Engineering Aide Second Class (Naval Rating) |
What does E03 mean on hot tub?
AMBIENT AIR TEMPERATURE
E03 ERROR CODE AMBIENT AIR TEMPERATURE. REASON, THE TEMPERATURE IS TOO LOW. This error code is visible if the ambient air temperature is too low outside. The spa pump will not run if the air temperature is below 4-6°c.
Read also: How to solve ‘Start menu error’ after installing Windows security update in July
Why does my hot tub keep shutting off?
So, why does my hot tub keep tripping and turning off? The problem could be due to a worn GFCI breaker, moisture or corrosion inside the breaker box, damaged or loose wiring, or malfunctioning components. It could even be down to a bad heating element or a flooded blower.
Why does my hot tub keep beeping?
Have you changed your filter recently? A dirty filter will block the water from circulating your filter housing and a safety cut off valve will kick in to avoid breaking the pump displaying warning E02. This is one of the main causes of the alarm being set off.
Where is the reset button on my hot tub?
The reset button is located in the equipment compartment. Plug the spa back into the power source. Check the circulation pump if the spa does not heat while jets and lights are working. This may be caused by the circulation pump thermal cut-off being tripped.
What does E02 mean on a hot tub?
E02 After starting or during the functions of filtering or/and heating, the water flow sensors do not detect water flow. 1. The 2 stopper caps have not been removed from inside the spa. Remove the filter set from inside the spa and push the filter or heat button. What does e03 mean on hot tub? E03 means that the water temperature is lower than 4ºC.
Why do I get the E02 error on my Coleman water pump?
If you try to start your water pump with no water in the tub or with the water level below the filter inlets, you will get this error. This only makes sense since the E02 error indicates a problem with water flow. If there is no water there, it cannot flow.
Why is my Coleman lazy spa E02 not working?
Here are some common Reasons Why Lazy Spa E02 And Lazy Spa E08 occur: You might see few other error codes on your Coleman Lazy Spa control panel like lazy spa E08, lazy spa E03, And lazy spa E02. You can troubleshoot all the error codes by pressing the lay z spa thermal reset button which you will find at the side of the lazy spa heater.
What does E03 mean on Coleman saluspa hot tub?
E03 error code: 1,Turn on the treadmill , motor running a few seconds then stop and console board shows E03, probably the Speed sensor issue. What does eo1 mean on hot tub?
